收藏本站
Precautions
Be sure to read the precautions and information common to all Snap Action and Detection Switches, contained in the Technical User’s Guide,
“Snap Action Switches, Technical Information” for correct use.
■ Correct Use
Mounting
Mount the switch onto a flat surface. Mounting on an uneven surface
may cause deformation of the switch, resulting in faulty operation or
breakage in the housing.
Operating Stroke
Take particular care in setting the operating stroke for the pin plunger
models. Make sure that the operating stroke is 70% to 100% of the
rated OT distance. Do not operate the actuator exceeding the OT dis-
tance, otherwise the life expectancy of the switch may be shortened.
Using Microloads
Using a model for ordinary loads to switch microloads may result in
faulty operation. Instead, use the models that are designed for
microloads and that operate in the following range;
■ Cautions
Handling
Turn OFF the power supply before mounting or removing the switch,
wiring, or performing maintenance for inspection. Failure to do so
may result in electric shock or burning
Terminal Connection
When soldering the lead wire to the terminal, first insert the lead wire
conductor through the terminal hole and then solder.
Make sure that the capacity of the soldering iron is 60 W maximum.
Do not take more than 5 seconds to solder the switch terminal.
Improper soldering involving an excessively high temperature or
excessive soldering time may deteriorate the characteristics of the
switch.
Be sure to apply only the minimum required amount of flux. The
switch may have contact failures if flux intrudes in the interior of the
switch.
Use the following lead wires to connect to the solder terminals;
30
0.16mA
26mA 100mA
Model
Conductor size
SS-5
0.5 to 0.75 mm 2
24
SS-10
0.75 mm 2
Operating range
for micro load
models SS-01
Operating
range for
general-load
models
If the PCB terminal models are soldered in a solder bath, flux will per-
meate inside the switch and cause contact failure. Therefore, manu-
ally solder the PCB terminal.
12
5
Inopera b le
range
1mA
SS-5, SS-10
100mA 160mA
Wire the quick-connect terminals (#110) with receptacles. Insert the
terminals straight into the receptacles. Do not impose excessive
force on the terminal in the horizontal direction, otherwise the termi-
nal may be deformed or the housing may be damaged.
Insulation Distance
0
1
10
100
1,000
Use a separator between the switch and metal mounting panels, to
C u rrent (mA)
However, even when using microload models within the operating
range shown above, if inrush current or inductive voltage spikes
occur when the contact is opened or closed, then contact wear may
increase and so decrease the service life. Therefore, insert a contact
protection circuit where necessary.
ensure proper dielectric characteristics are achieved.
According to E N 61058-1, the minimum insulation thickness for this
switch should be 1.1 mm and minimum clearance distance between
the terminal and mounting plate should be 1.6 mm. If the insulation
distance cannot be provided in the product incorporating the switch,
either use a switch with insulation barrier or use a separator to
ensure sufficient insulation distance.
Separator
Snap Action Switch
SS
101
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
SSCEA31C SWITCH LIMIT WHEEL PLUNG SPDT
SSPT7F-7PF20-R CRYSTAL 32.768KHZ 7PF SMD
ST3215SB32768E0HPWZZ CRYSTAL 32.768KHZ 9.0PF SMD
ST363016LG BOX STEEL 41.8X30X16" GREY
ST603616SS BOX ST STEEL 65.8X36X16" NAT
ST68-100T2MI CAP TANT 68UF 100V 20% AXIAL
STE6000-16T4MI CAP TANT 6000UF 16V 20% AXIAL
STHW-690-N SWITCH TACTILE SPST-NO 0.05A 12V
相关代理商/技术参数
SS5GL7016D 制造商:Omron Corporation 功能描述:RELAYS MISC - Bulk
SS5GL8025D12 制造商:Omron Electronic Components LLC 功能描述:SUBMINIATURE BASIC SWITCH - Trays
SS-5GL8025D-12 功能描述:基本/快动开关 Subminiature Basic Switch RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel
SS5GL8030T 制造商:Omron Electronic Components LLC 功能描述:SUBMINIATURE SNAPACTION SWITCH - Trays
SS-5GL8030T 功能描述:基本/快动开关 Subminiature Snap Action Switch RoHS:否 制造商:Omron Electronics 触点形式:SPDT 执行器:Lever 电流额定值:5 A 电压额定值 AC:250 V 电压额定值 DC:30 V 功率额定值: 工作力:120 g IP 等级:IP 67 NEMA 额定值: 端接类型:Wire 安装:Panel
SS5GL999 制造商:Omron 功能描述:subminiture switch
SS5GL999D 制造商:Omron 功能描述:Detection Switch
SS-5GLBYOMI 制造商:Omron Electronic Components LLC 功能描述:SWITCH SS-5GL